OptiWand 3 Pack Soft Contact Lens Insertion Removal Tool. All Eye Lens Inserter

Description: This listing is for a box of 3 OptiWand® ‘s. Colors are Blue or Green OptiWand is made of SOFT PLIABLE RUBBER & Is a Soft Contact Lens Insertion & Removal Tool.APPLYING EYE DROPS PRIOR TO INSERTION IS A MUST FOR THIS TO WORK PROPERLY!! It helps transfer the lens from wand to eye and vice versa much easier.It can be used to INSERT ALL CONTACT LENSES.It WILL remove soft contact lenses with some practice & patience by PINCHING THEM WITH THE SOFT ENDS!****************IT IS NOT A SUCTION CUP FOR SOFT LENSESWe strongly recommend starting with insertion as it should be easier to perfectRemoval's pinch can be tricky but once mastered it is super simplePractice and patience are a must and old habits must be broken in order to use it properlySoft contact lenses are NOT a SOLID material and CANNOT be grabbed by placing the OptiWand against themYou must break the bond between contact lens & your CORNEA where your lenses sit securely as designedIT WILL NOT Remove RGP/Hard/Sclera lenses The Split Cup side will insert Sclera lenses and either side will insert RGP *It has an EMERGENCY BLINK RELEASE TO PREVENT STICKING TO NAKED EYE *For proper insertion you must focus on the CENTER HOLE and not a mirror or other source. The soft contact LENS WILL NOT come off the OptiWand unless it is placed properly directly on the cornea. If you are bringing it in at an angle the contact lens will stay on the OptiWand and not come off on to the eye as intended. Using OptiWand for inserting SOFT & HARD Contact Lenses Step 1: Apply Eye Drops prior to use! Dip your OptiWand in Contact Lens solution for lubrication.Step 2: Position your regular sized HARD or SOFT contact lens on the center of FULL CUP SIDE of the OptiWand. If you have small soft eyes or hard lenses you can use the SPLIT CUP end and use the following steps. The OptiWand is designed to hold the lens during insertion.Step 3: Using your non-dominant hand spread your eye lids as wide as possible, keeping your eyelashes out of the way.Step 4: Draw the OptiWand to your eye by looking DIRECTLY AT THE LENS through the CENTER HOLE to align properly.*Aiming the OptiWand at a colored background or light will help some to focus on the CENTER HOLE*Step 5: Once it is close enough and the contact lens touches your eye, give the OptiWand a slight TWIST to help release the lens. Step 6: Blink your contact into place. Now your lens is centered on your eye.* Make sure to hold eyelashes away to prevent blockage. *WARNING **NEVER USE OptiWand ON NAKED EYE**Please DO NOT USE the OptiWand if you are allergic to Liquid Silicone Rubber!Using OptiWand for Removing SOFT Contact LensesYOU CAN USE THE FULL CUP OR SPLIT CUP TO PINCH SOFT LENSES.SPLIT CUP END IS BEST IF YOU HAVE SMALL EYES OR LENSES.FULL CUP END IS BEST FOR LARGER FINGERS OR LONG FINGERNAILS.Step 1: Apply Eye Drops prior to use! We suggest using a DRY OptiWand for Soft Contact Lens removal for best results.Step 2: Using your non-dominant hand spread your eye lids as wide as possible, keeping your eyelashes out of the way.Step 3: Focusing through the CENTER HOLE, draw the OptiWand to your eye until you touch the soft contact lens.Step 4: Once you feel the OptiWand touch the soft contact lens you should twist it slightly then carefully pinch the soft contact lens with the Base of the OptiWand and swipe away from eye. Some users can turn the OptiWand towards their noses after it makes contact and that will help push it out.*Best pinching position is very close to the tip* Final Step: Dip OptiWand into contact lens solution in current case and the lens will fall down into the solution with a pinch on the Full cup. We suggest placing the soft lens on your non dominant index finger and PRACTICE THE PINCH OFF OF YOUR FINGER to get a feel for actual removal.If you pinch the soft contact lens off of a finger a few times you will be able to visualize what it takes to pinch effectively. Using OptiWand for inserting Large Sclera contact lensesStep 1: Dip your OptiWand SPLIT CUP SIDE in Contact Lens solution for lubricationStep 2: Stand the OptiWand up on the counter or table top with the Split cup side upStep 3: Position your Sclera contact lens on the center of the SPLIT CUP SIDE of the OptiWand Step 4: Look & stay focused on the CENTER HOLE for proper alignment. * Some prefer to have a colored background to help focus on the CENTER HOLE *Step 5: Spread your eye lids as wide as possible, keeping your eyelashes out of the way.Step 6: Slowly draw to the OptiWand until the contact lens makes contact with the eye.Step 7: Blink until comfortable USE ONLY AS DIRECTED!These statements have not been evaluated by the Food and Drug Administration.This product is not intended to diagnose, treat, cure, or prevent any disease.Please read and follow instructions as well as view the instructional videos for best results.OptiWand®, OptiWand Pincher®, OptiWand Bullseye®, OptiWand Hard®,OptiCase® & OptiAide are disposable products.We suggest replacing after 30 Days if used daily.To clean use soft soap, rinse thoroughly and air dry. Not dishwasher tested.Please DO NOT USE any OptiWand® if you are allergic to Liquid Silicone Rubber!OptiWand®, OptiWand Pincher®, OptiWand Bullseye®, OptiWand Hard® & OptiCase® are registered trademarks of TJSC Optix Inc.No claim is made to the exclusive right to usethe following part from the mark as shown: “Hard”No claim is made to the exclusive right to usethe following part from the mark as shown: “Pincher”All rights reserved.Patent No. Des. D791,858SPatent No. Des. D806,387SPatent No . Des. D898,814 S

Price: 18.99 USD

Location: Longwood, Florida

End Time: 2024-02-29T21:24:53.000Z

Shipping Cost: 0 USD